Biddle CA M-150-W-F Скачать руководство пользователя страница 23

Страница: 23 / 60

SER

’

AND

NSTALLER

’

ANUAL

NSTALLATION

Version: 4.0 (23-08-2007)

Adjusting discharge duct

If linking two or more units to each other, you must adjust the

discharge duct so that the finishing edges will not be in each

other’s way.

1. Remove the end piece with finishing edge

2. Mount the end piece without finishing edge

Mounting discharge duct

3. Make a hole in the ceiling for the discharge (for dimen-

sions, see

Table 2-2

4. Fix the two angle sections

with sheet metal screws to

the unit, along the edges of the discharge opening.

5. Slide the discharge duct

into the discharge opening until

the desired height is reached.

6. Using sheet metal screws, fix the discharge duct to the

angle sections

Table 2-2

Discharge section hole dimensions

EFERENCE

YPE

IMENSIONS

CA S-R

102 mm

CA M-R

102 mm

CA L-R

133.5 mm

CA XL-R

133.5 mm

CA 100-R

1,008 mm

CA 150-R

1,508 mm

CA 200-R

2,008 mm

CA 250-R

2,508 mm

Содержание CA M-150-W-F





























































Результаты поиска

Содержание CA M-150-W-F

Отзывы:

Biddle CA M-150-W-F, Руководство пользователя и инсталлятора, Страница: 23 / 60

Результаты поиска

Содержание CA M-150-W-F

Отзывы: