Biddle CA M-150-W-F Скачать руководство пользователя страница 10

Страница: 10 / 60

NTRODUCTION

OMFORT

URTAIN

1.4

Safety instructions

1.4.1 Operation

Warning:

Do not put any objects in the inlets and outlets.

Warning:

Do not block the inlets and outlets.

Warning:

The upper surface of the unit becomes hot during

operation.

1.4.2 Installation, maintenance and service

Danger:

The unit may be opened by qualified technical staff

only.

Warning:

Perform the following actions before opening the

unit:

1. Switch the unit off using the control panel.

2. Wait until the fans have stopped.

3. Allow the unit to cool down.

The heat exchanger or, as the case may be, the heating ele-

ments can get very hot. Moreover, the fans may keep on

rotating for a while.

4. Disconnect power supply (remove plug from socket or

move isolation switch to Off).

For water-heated models:

close the main water supply (if

possible).

Warning:

The fins of the heat exchanger are sharp.

Содержание CA M-150-W-F





























































Результаты поиска

Содержание CA M-150-W-F

Отзывы:

Biddle CA M-150-W-F, Руководство пользователя и инсталлятора, Страница: 10 / 60

Результаты поиска

Содержание CA M-150-W-F

Отзывы: