manualshive.com logo in svg

Biddle CA M-150-W-F, Руководство пользователя и инсталлятора, Страница: 11 / 60

Поделиться
Скачать
Biddle CA M-150-W-F Скачать руководство пользователя страница 11

U

SER

’

S

 

AND

 I

NSTALLER

’

S

 M

ANUAL

I

NSTALLATION

Version: 4.0 (23-08-2007)

11

2

.  .  Installation

2.1

Safety instructions

Danger:

d

Installation works on the unit may be performed by 

qualified technical staff only.

Warning:

w

Before opening the unit, follow the safety instruc-

tions in section 

1.4

.

2.2

Delivery check

1. Check the unit and its packaging for correct delivery. 

Immediately report to the supplier any damage caused in 

transit.

2. Make sure that all components and accompanying parts 

have been supplied. 

2.3

General working method

Working method

Biddle recommends the following working method for instal-

ling the comfort air curtain:

1. Mount the unit (section 

2.4

).

2.

For water-heated models (CA W and CA H): 

connect the unit 

to the central heating system (section 

2.5

).

3. Connect the unit to the power supply (section 

2.6

).

4. Install the control panel and (any optional) connections to 

external controls (section 

2.7

).

5. Finish the unit (section 

2.8

).

6. Turn on the power supply and check the working of the 

unit (section

2.9

).

Содержание CA M-150-W-F





























































Отзывы:

Нет отзывов