background image

SENSseries LB 480 Level measurement
BERTHOLD TECHNOLOGIES GmbH & Co. KG

3 – 331

Volume 3

Menu Structure

3

2.18

Signal Dependency

Menu path: 

Device Config 

 Setup 

 Signal Condition 

 Signal 

Dependency

.

Use this menu, for example, to detect external radiation from weld 
inspections, or short-term use of other sources in the vicinity of the 
detector.

If the current count rate exceeds the threshold set in 

Io Factor 

or 

in

 RI Sigma

, the interference radiation warning will be issued. In 

this case:

the measured value is frozen and

the current output holds the last measured value

The measurement remains frozen as long as the external radiation 
is present, plus the waiting time that has been set in Waiting Time.

To get the warning messages, you have to evaluate the messages 
via the HART

®

 signal or the digital output.

IMPORTANT

If interference radiation detection is enabled, the measured values 
are output with a delay. The delay is adjustable from 0 to 5 sec-
onds.
The delay is required so that at the moment of detection the mea-
sured value remains unaffected, even though in this case, 
increased count rates are already present. For this reason, while 
interference radiation detection is active, no applications can be 
run where the reaction time must be below the set delay.

For detailed information please refer to the section Interference 
Radiation Detection (

chapter 7.5, page 3-420

).

1 Response Mode

Additional parameters are displayed, depending on which function 
you select.

Select the detection mode:

• DISABLED

Interference radiation detection and Rapid switchover are dis-
abled.

• RAD. INTERFERENCE

Interference radiation detection is enabled.
For detailed information please refer to the section Interference 
Radiation Detection (

chapter 7.5page 3-420

).

• RAPID SWITCH

Rapid switchover is enabled.
The use of the function 

RAPID SWITCH

 is recommended only 

for special applications where the output signal has to adapt 
rapidly to the new value, e.g. for measurements on small con-
tainers and if sudden level changes occur.

Содержание LB 480



































































































































































































































































































































































































































































Отзывы: