manualshive.com logo in svg

BERTHOLD TECHNOLOGIES LB 480, Руководство пользователя, Страница: 371 / 450

Поделиться
Скачать
BERTHOLD TECHNOLOGIES LB 480 Скачать руководство пользователя страница 371

SENSseries LB 480 Level measurement
BERTHOLD TECHNOLOGIES GmbH & Co. KG

3 – 371

Volume 3

Menu Structure

3

2.42

Plateau Measurement

Menu path: 

Device Config 

 Setup 

 Service 

 Plateau 

 

Plateau Measurement

.

For information on how to perform a plateau measurement please 
refer to 

chapter 6.2

, 

page 3-406

.

1 Active Detector No.

Choose the detector for which you want to record a plateau.

•

Detector No.

 = 

0

 selects the master detector.

•

Detector No.

 = 

1

 selects slave 1.

•

etc.

2 HV Start

Enter the HV start value in volts.

3 HV Stop

Enter the HV stop value (end value of the measurement) in 
volts.

4 HV Step

Enter the step size in volts, which should lie between the mea-
suring points.

5 Meas. Time

Enter the length of time over which each measuring point 
should be averaged, for example 20 s. 

6 HV Mode

The menu item offers the following options:

•

AUTO

 

Enables the automatic HV control. Set this operating mode for 
the normal measurement mode. This enables a temperature-
stable operation of the detector.

•

MANUAL

 

This setting is typically used for testing purposes only. You can 
specify, for example, the provisional operating point of the 
detector. The specified voltage must, however, lie in the pla-
teau.
As soon as you enable 

Manual

, the automatic HV control is 

switched off. The HV is then set to the value that was specified 
at HV Manual.

•

PLATEAU

 

Starts the plateau measurement. The measurement mode is 
exited and the plateau of the multiplier which is used in the 
detector is measured. The measurement is done with the set-
tings defined in the menu items 

HV Start

, 

HV Stop

, 

HV Step 

and 

Meas. Time

.

At the end of the plateau measurement the detector automati-
cally switches back to 

HV Mode

: 

AUTO

 or 

MANUAL

, depend-

ing on which mode was last set.

Содержание LB 480



































































































































































































































































































































































































































































Отзывы:

Нет отзывов