BERTHOLD TECHNOLOGIES LB 480 Скачать руководство пользователя страница 233 | Manualshive

Страница: 233 / 450

background image

SENSseries LB 480 Level measurement
BERTHOLD TECHNOLOGIES GmbH & Co. KG

2 – 233

Volume 2

4 Repair, Maintenance and Upkeep

2

4.3.2

Installing the Electronics Module

Reassemble the electronics module in reverse order.



Connect the wires between connection head and electronics
correctly.



Check that the wires sit firmly in the terminals.



Replace the O-ring that seals the housing.



Make sure that neither moisture nor metal chips are present in
the connection box.



Carefully insert electronics module with the crystal-multiplier
assembly again into the housing.



Attach the connection head to the detector housing again.
Tighten screws evenly alternating between screws.



Close the housing carefully with the housing cover. To do this,
put the housing cover with the sealing on the housing and
tighten the Allen screws using the specified torque: depending
on the version, M5 with 4 Nm or M8 with 17 Nm (standard val-
ues).

If you have installed a new electronics module:



Place the supplied sticker over the number of the Dev. ID on
the type plate.



Turn on the power supply of the detector again.



Set the software parameters again using the list you have
noted down at the beginning. See also

on

Separate User’s Manuals are available for user interfaces such
as SIMATIC PDM or FOUNDATION

™

Fieldbus.

This completes the replacement of the electronics module.

«
...
231
232
233
234
235
...
»

Содержание LB 480



































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LB 480

Бренд: Yamaha Страницы: 2

Бренд: Teac Страницы: 148

Бренд: IFM Страницы: 25

Бренд: Campbell Страницы: 16

Бренд: 3B6 Страницы: 30

Бренд: Kane Страницы: 19

Бренд: XS Scuba Страницы: 24

Бренд: Nady Audio Страницы: 2

Бренд: VEE GEE Страницы: 2

Бренд: Vaisala Страницы: 2

Prestige Series

Бренд: Ibanez Страницы: 54

Бренд: SICK Страницы: 68

Бренд: OHAUS Страницы: 84

Бренд: PANCONTROL Страницы: 157

Бренд: Hanna Instruments Страницы: 2

Бренд: Vogel Страницы: 4

K-PATENTS PR-23 AX Series

Бренд: Vaisala Страницы: 246

LaserRange-Master T4 Pro

Бренд: LaserLiner Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды