manualshive.com logo in svg

BERTHOLD TECHNOLOGIES LB 480, Руководство пользователя, Страница: 227 / 450

Поделиться
Скачать
BERTHOLD TECHNOLOGIES LB 480 Скачать руководство пользователя страница 227

SENSseries LB 480 Level measurement
BERTHOLD TECHNOLOGIES GmbH & Co. KG

2 – 227

Volume 2

4 Repair, Maintenance and Upkeep

2

4

Repair, Maintenance and 
Upkeep

IMPORTANT

Spare parts for detectors used in the Ex-area must be mounted 
solely by the BERTHOLD TECHNOLOGIES service or by persons 
authorized by BERTHOLD TECHNOLOGIES. If this is not possible, 
you must replace the entire detector or return it to the manufac-
turer for repair.

For devices that are 

NOT

 used in an Ex-area, the following parts 

may be replaced at your own risk and taking into account a loss of 
any existing warranty by BERTHOLD TECHNOLOGIES:

–

the complete detector electronics

–

the complete connection head

–

the crystal at the CrystalSENS

–

the multiplier (PMT)

–

the multiplier crystal combination

–

the detector housing

BERTHOLD TECHNOLOGIES recommends to have detectors 
repaired solely by the BERTHOLD TECHNOLOGIES service or by per-
sons authorized by BERTHOLD TECHNOLOGIES.

Only original spare parts by BERTHOLD TECHNOLOGIES may be 
used.

Please follow the instructions in the Safety Manual (

Volume 1

) and 

the instructions in 

chapter 3

, 

"Electrical Installation", page 2-217

.

After every repair, maintenance or upkeep, please use the check-
lists on 

page 1-51

 and 

page 1-53

.

Содержание LB 480



































































































































































































































































































































































































































































Отзывы:

Нет отзывов