BERTHOLD TECHNOLOGIES LB 480 Скачать руководство пользователя страница 409

Страница: 409 / 450

SENSseries LB 480 Level measurement
BERTHOLD TECHNOLOGIES GmbH & Co. KG

3 – 409

Volume 3

6 Functional Processes

Risk of fatal injury due to electric shock!

If the housing is open you may come into contact with live parts if
the power supply is connected.

The Master Reset has to be carried out with open housing cover
and the power supply turned on. Power supply is applied to the ter-
minals 1 to 4.

Furthermore, high voltage is present in the area of the base of the
board for the photomultiplier.

Perform Master Reset

1. Disconnect detector from mains.

2. Open housing.

3. Plug bridge on connector "F" (the connector is located on the

CPU board next to the large capacitor).

4. Turn detector on and wait 10 seconds.

5. Turn detector off again.

6. Pull bridge off connector "F".

7. Turn detector on and wait 10 seconds.

8. Turn detector off again.

9. Connect HART

Communicator to the current output in the ter-

minal compartment.

10. Turn detector on again and wait 10 seconds.

11. Acknowledge error message on HART

Communicator.

12. Enter License Key new, menu

Device Config



Setup



Service



License Key

, see

chapter 2.35

page 3-363

13. Adjust current output with multimeter, menu

Device Config



Setup



I/O Setup



Current Out



D/A trim

, see

chapter 2.29

page 3-355

IMPORTANT

The adjustment is absolutely essential, even if the current output
appears to be OK.

14. Enable monitoring of the 4-20 mA current signal (set to

ENABLED

), menu

Device Config



Setup



I/O Setup



Current Out



Current Loop Monitoring

15. Set

Detector Code

, menu

Device Config



Setup



Sensor

Configuration



Sensor Settings



Detector Code

, see

page 2-166

16. Set

HV Default

, see

chapter 5.1.2

This completes the reset, the detector is now ready for cali-
bration.

Содержание LB 480



































































































































































































































































































































































































































































Результаты поиска

Содержание LB 480

Отзывы:

BERTHOLD TECHNOLOGIES LB 480, Руководство пользователя, Страница: 409 / 450

Результаты поиска

Содержание LB 480

Отзывы: