manualshive.com logo in svg

BERTHOLD TECHNOLOGIES LB 480, Руководство пользователя, Страница: 414 / 450

Поделиться
Скачать
BERTHOLD TECHNOLOGIES LB 480 Скачать руководство пользователя страница 414

54733-10BA2L 

3 – 414

02.2017

7 Explanations

Volume 3

Agitator

•

The agitator must be in operation if it has any impact on the 
measurement.

High gas pressure

•

If the container is under high gas pressure during operation, 
the empty calibration also has to be carried out under this gas 
pressure. If this is not possible, then the empty calibration can 
be done without gas pressure and the count rate can be com-
pensated using the 

GDA

 function and the corresponding entries 

for gas density and measuring path.

Cooling and heating jackets

•

Cooling and heating jackets must be filled for calibration. In 
order to get the density of the cooling/heating fluid, it should be 
at the same temperature as during operation.

Содержание LB 480



































































































































































































































































































































































































































































Отзывы:

Нет отзывов