BERTHOLD TECHNOLOGIES LB 480 Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 450

BERTHOLD TECHNOLOGIES LB 480 Скачать руководство пользователя страница 143

SENSseries LB 480 Level measurement
BERTHOLD TECHNOLOGIES GmbH & Co. KG

1 – 143

Volume 1

10 Source Replacement

1

Health hazards due to radiation!

Do not remove the source from the shielding!

Do not touch the source to prevent a high partial body dose. Touch
the source only with a tool that allows you to hold the source easily
and safely. Keep the source far away from your body and set it
down behind an auxiliary shielding.



Screw the source holder (6) together with the source (7) using
a socket wrench (size 12 mm).

Remove source from shielding



Unscrew the source from the source holder using a socket
wrench (size 10 mm). Hold the source holder using a second
socket wrench (size 12 mm).

IMPORTANT

For this work, you should use the shielding housing as auxiliary
shielding between source and body.



Take hold of the source using a pair of pliers and immediately
put it into the transport shielding or another shielding.

IMPORTANT

Make sure the source is not mixed up with the new or another
source.



If necessary, clean and grease the thread on the source holder
and the shielding.

Install new source



Using a pair of pliers, take the new source out of the transport
shielding and firmly fix it onto the source holder together with
the locking washer (torque: 3.5Nm).



Put the source holder with the source again into the shielding
and fix it using the socket wrench (torque: 44Nm).



Check the proper ON/OFF function.



Carefully close the transport shielding again, after you have put
the old source into the transport shielding.

«
...
141
142
143
144
145
...
»

Содержание LB 480



































































































































































































































































































































































































































































Отзывы:

Нет отзывов