Bell System bellagio Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 52

background image

bellagio Digital Entry System

PD

–

281 Issue 1

Installation and Operating Manual

Page 24 of 52

Commissioning

Settings

1. Set the flat addresses of each DBA-4I or DBA-8Z Isolator referring to the following

sections.

2. Entrance and caller settings (speech time, ring time, unlock time, etc) are adjusted

through each entrance panel at the associate entrance.

Refer to the ‘Entrance

panel programming’ section page

3. Settings specific to each phone, such as ring volume and buzzer mute time, when

available, are set inside each phone with a jumper or Dipswitch.

Refer to the ‘Phone

Settings’ section.

4. Speech levels are adjusted at each entrance panel behind the speech grill, with a

separate adjustment for each direction of speech. A howling or whistling sound may
indicate the volumes levels are set to high.

Testing / Connecting

The major components of the

Digi

bell system are fitted with high quality pluggable screw

terminal blocks. This enables all the connections to the system to be fully completed,
whilst easily isolating individual pieces of equipment during testing and commissioning.

Any problems can be resolved by rechecking wiring and connections, assisted by the

various suggestions and tests in the section ‘Troubleshooting’.

Connect up one entrance first, leaving any connection to Isolators or phones unplugged:

1. When powered up for the first time, it is recommended that only the most basic

system is connected, i.e. 4/8 phones, 1 BSD-DIG Door controller and entrance
panel, 1 DBA-xx Isolator, the remaining equipment can be isolated by removing
terminal blocks.

2.  Check the display and buttons on the entrance panel work as expected.
3.  If there is an exit button check the door will unlock.
4.  Proceed  to  test  the  system  by  calling  each  phone  from  the  entrance  panel  in  the

normal way, check any available phone features such as buzzer mute or door
status. Once the basic system is fully functioning, continue to connect and test
equipment item by item until completed.

«
...
22
23
24
25
26
...
»

Содержание bellagio





















































Отзывы:

Нет отзывов

Похожие инструкции для bellagio

Бренд: JBL Страницы: 2

Spacemaker 7-5400

Бренд: GE Страницы: 12

Бренд: Safeline Страницы: 28

Бренд: Safeline Страницы: 8

Бренд: Xtrons Страницы: 30

Бренд: Sandstrom Страницы: 32

Бренд: PAC Страницы: 12

Бренд: Livoo Страницы: 6

Бренд: ICP DAS USA Страницы: 8

Бренд: Daewoo Страницы: 35

Бренд: 2N Страницы: 132

Бренд: JUNGLE HOBBIES Страницы: 37

Бренд: Beta Three Страницы: 10

Бренд: COBHAM Страницы: 179

9846A SPEAKER SYSTEM

Бренд: Altec Lansing Страницы: 1

Satellite Centerspeaker I Compose

Бренд: Loewe Страницы: 40

Бренд: Alpine Страницы: 16

Clementine 8440

Бренд: PNI Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды