Bell System bellagio Скачать руководство пользователя страница 27

Страница: 27 / 52

bellagio Digital Entry System

–

281 Issue 1

Installation and Operating Manual

Page 27 of 52

TRADE FUNCTION

–

Door Button Trades Mode

Choose the Mode value 0-9

Setting

[0]

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

Time Clock Off None None None None Code

Code

Code Trade Trade Door

Time Clock On None Door Code Trade Trade

Door

Code Trade Door Door

‘None’

= No function; pressing the

door

button is ignored.

‘Door’

= Pressing the

door

button opens the door.

‘Code’

= Pressing the

door

button prompts for the Access Code to open the door.

‘Trade’

= Pressing the

door

button prompts for either the Access Code or Trades Code

to open the door.

DOOR MON POL

–

Door Status Switch

[Owc]

= Contacts open when door is closed:

–

The default allows for no switch fitted.

[Cwc]

= Contacts closed when door is closed:

–

Standard normally closed switch.

RECPTION No

–

Reception Phone Address

The

reception

button is used to call a reception desk or similar. The number is that of the

called phone. The default is [9898] which is unlikely to be used by a flat.

SECURITY CODE

–

Panel Security Key

The security key is required to gain access to panel programming.

The code is entered then pressing the

bell

button, the default is [3434] and it is

recommended that this be changed for security.

This code can contain letters and numbers for added security.

PHONE CODE

–

Phone Programming Security Key

The  phone  programming  security  key  is  required  to  gain  access  to  flat  number
programming  of  telephones.    The  default  is  [1212]  and  it  is  recommended  that  this  be
changed for security.

This code can contain letters and numbers for added security.

This function is for when the BFD-DIG is used in systems where isolator programming
cannot cope with the required complexity.

Содержание bellagio





















































Результаты поиска

Содержание bellagio

Отзывы:

Похожие инструкции для bellagio

Бренды по названию

Популярные бренды

Bell System bellagio, Руководство по установке и эксплуатации

Результаты поиска

Содержание bellagio

Отзывы:

Похожие инструкции для bellagio

Бренды по названию

Популярные бренды