Bell System bellagio Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 52

background image

bellagio Digital Entry System

PD

–

281 Issue 1

Installation and Operating Manual

Page 25 of 52

BFD-DIG Door Controller Settings

The BFD-DIG is programmed from the panel for all settings.

Security

It is strongly recommended that the Panel Security Code be changed from its factory
setting to prevent unauthorised access. Record the new number carefully as it cannot be
easily changed if lost. It is also recommended that the Phone Programming Code, Coded
Access Code and Trades Access Code are all changed from default even if not used.

To access panel programming without the code requires physical access to the controller
PCB, borrow a jumper from say video gain (remember the setting) and place it on the 6 pin
programming header between pins 5 & 6. Now pressing the test button will enter panel
programming for 30S when the panel security code can be read or set. When the
programming is finished replace the jumper back to its original location.

Panel Programming



First type the Panel Security Code (initially [3434]) followed by the

bell

button.



The display will show the first programmable parameter and the current value.

Numeric Entry

Bell Button Toggles Value



Press the

key

button to step down through the programmable parameters.



Press the

reception

button to step up through the programmable parameters.



N.B. The display may take up to 2 Seconds to refresh.



The list rolls over bottom to top and vice versa.



To change a numeric parameter simply type a new 1-4 digit value and then press

bell

.



To change other values simply press

bell

to choose the next value.



To exit Panel Program Mode press

cancel

.



If no button is pressed for 30 seconds then programming mode will auto-cancel.

«
...
23
24
25
26
27
...
»

Содержание bellagio





















































Отзывы:

Нет отзывов

Похожие инструкции для bellagio

Бренд: Panasonic Страницы: 2

Бренд: Samsung Страницы: 77

Бренд: Neets Страницы: 14

Бренд: Onkyo Страницы: 10

Бренд: E. DOLD & SOHNE Страницы: 28

DUOX plus iLOFT 3450

Бренд: Fermax Страницы: 2

CONPROSYS CPS-MC341-DS1-111

Бренд: Contec Страницы: 71

BeoSound 3000 2671

Бренд: Bang & Olufsen Страницы: 68

Бренд: Acard Страницы: 2

Nitrogen Pac SC-W

Бренд: UNITED Страницы: 112

Бренд: JBL Страницы: 6

Amp Master - 6ch

Бренд: Involve Audio Страницы: 4

Бренд: PAPILLON Страницы: 8

Бренд: Watts Страницы: 16

Бренд: Sherwood Страницы: 6

Бренд: Pulse Страницы: 14

Бренд: GAS Страницы: 2

Бренд: M-system Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды