9-8
Removing and Replacing Wire Cables
9-8-1
Several wire cables are used in this instrument:
•
on the Return Feed Assembly (see item 22 on Figure 9-3, page 9.6).
•
on the Infeed Rack Feed Assembly (see items 36 and 37 on Figure 9-4, page 9.8.
•
and on the Outfeed Rack Feed Assembly (see items 36 and 37 on Figure 9-4, page 9.8.
9-8-2
If it becomes necessary to remove and/or replace a wire cable, use the following procedures.
9-8-3
To Remove a Wire Cable:
1
Note the proper routing of wire cables around winding drums, pulleys and bearings
before
removing wire
cables from each of the assemblies. If necessary, draw a picture showing proper cabling route of the wire
cable to be replaced.
2.
Wire cables are removed by removing their two end nuts, washer, spring and flange bushing (see Figure
9-3 on page 9.6 or Figure 9-4 on page 9.8). Then, thread the cables off the pulleys and bearings. Finally,
remove wire cable ends from the winding drums attached to the motors by carefully prying the ends out of
the drums.
9-8-4
To Install a Wire Cable:
1.
Install wire cable ends into Winding Drum attached to motor. Drums have slots cut into them to receive the
wire cable ends. See Figure 9-8 for proper installation when the assemblies are at home position. Home
position is when the assembly has reached its full travelling position with the assembly metal Tab
bisecting the ORG sensor.
2.
Route new wire cables in same sequence as the old wire cables (see Figures 9-3, 9-4 and 9-8).
3.
Re-attach flange bushing, spring, washer and two end nuts. Wire cable deflection should be
approximately one inch (25mm) when measured from the middle of the furthest distance of the cable (see
Figure 9-9).
4.
Once cables are installed, re-assemble unit and run With Tube Run in Service Mode (see page 7.4) for 30
minutes to verify instrument was set up correctly.
Figure 9-9 Wire Cable Deflection
9-17
Содержание Clinitek Atlas
