manualshive.com logo in svg

Bayer HealthCare Clinitek Atlas, Руководство по обслуживанию, Страница: 155 / 185

Поделиться
Скачать
Bayer HealthCare Clinitek Atlas Скачать руководство пользователя страница 155

Older model 

5001A

 units should first be retrofitted to model 5001 X before adding this new model 5023 to 

them: see service bulletin ATLAS-008 for more information. 
 
A newer Clinitek Atlas model 

5001C

 will soon be introduced which will accommodate model 5023 without any 

special retrofit or other hardware changes, see bulletin ATLAS-103 for more information regarding this new 
model. 
 

Bolt-On Takeup Reel Retrofit Kit 95002152 contains:

Part Number

Quantity 

1.

                                                                         

Bolt-On Takeup Reel Assembly

...............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

95001941

1 

2.

                                                                         

Drive Shaft Assembly

....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

95001945

1 

3.

                                                                         

Spacer Plate

.........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

50455536

1 

4.

                                                                         

Belt

........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

50035027

1 

5.

                                                                         

Socket Head Cap 

Screw, 

1/4 - 20 x 1.00 inch

.................................................................................................................................................................................................................................................................................................

835-2389-01

4 

6.

                                                                         

Split Lockwasher, 1/4 inch

.................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

50333019

4 

7.

                                                                         

Flat Washer, 1/4 inch

..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

557-7178-01

4 

8.

                                                                         

Timing Pulley

..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

50462026

1 

9.

                                                                         

Wire Tie

........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

50558004

1 

10.

                                          

Installation Instructions (this bulletin)

......................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

50241534

1 

11.

                                          

Drill Template Fixture

.......................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

50570144

1 

12.

                                          

Clinitek Atlas Operating Manual Insert

.................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

50241538

1 

13.

                                          

 Transfer Punch, .250 inch Diameter

.........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

50450250

1 

 

                                                            

To retrofit one Clinitek Atlas instrument with this kit, order one Bolt-On Takeup Reel Retrofit Kit 
95002152

, 

one Rack Sample Handler Door Kit 5298 and one V5.00 Update Kit 95002122.

 

 

Many instruments may already contain the new V5.00 Update Kit, confirm that this kit is needed before 
ordering it.  A mandatory retrofit to use Version 5.0 software will soon be done to all Clinitek Atlas 
systems. 

 

To Retrofit Model 5001X and Early 5001 B units to use New Model 5023: 

 

Tools Required:

•

                                                                                              

Electric Power Drill 

•

                                                                                              

Number 3 (or 3mm) Size Center Drill Bit 

•

                                                                                              

Letter H .266 inch (as close to 6.75mm as possible) Size Drill Bit 

 

Parts Required:

•

                                                                                              

Rack Sample Handler Door Kit (quantity of 1, product code 

5298

) 

•

                                                                                              

Bolt-On Takeup Reel Retrofit Kit Assembly, part number 

95002152

 

•

                                                                                              

V5.00 Update Kit (quantity of one, part number 

95002122

) 

 
Item and page numbers below refer to the Service Manual page where the part is pictured. 

 

1.

                                                                         

Go to Ready For Testing screen and record Strips Remaining total.  Go to Main Menu and do a 
PRINT SETUP or otherwise record all Setup selections.  Transfer all patient and control results to the 
computer and/or printer.  Remove used reagents from the Takeup Reel. 

 

2.

                                                                         

Go into Diagnostics and do a Replace Pipette.  Remove Pipette from instrument. 

 

3.

                                                                         

Turn off the Clinitek Atlas unit.  Remove the Sample Handler from the Clinitek Atlas system by 
removing the four 10-32 x 0.75 inch socket head alien cap screws. 

 

4.

                                                                         

Remove Left Door and its hinge (items 20 and 18, page 10.4) from instrument frame.  Remove Right 
Lower Door and its hinge (items 19 and 34, page 10.4) from the frame. 

 

5.

                                                                         

Remove Back Panel (item 11, page 10.4) and Right Side Panel (item 15, page 10.4) from Clinitek 
Atlas unit.  Note the top front alien screw may require using an elbow or ball-socket alien wrench to 
remove this right side panel. 

 

11-7

Содержание Clinitek Atlas


























































































































































































Отзывы:

Нет отзывов