Bayer HealthCare Clinitek Atlas Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 185

Bayer HealthCare Clinitek Atlas Скачать руководство пользователя страница 16

CHAPTER FIVE

PREVENTATIVE MAINTENANCE

5-1

Introduction

5-1-1

This chapter describes routine maintenance done by a customer and preventative maintenance to be
performed by a field engineer while on a service call.

5-2

Routine Maintenance

5-2-1

The

Transfer Plate

(top steel plate racks travel on) should be cleaned daily with a damp cloth and

mild detergent. Afterwards, dry the plate off with a clean, soft cloth.

A dirty Transfer Plate may

搒

queak?loudly during rack transfer and may cause rack jams to occur.

5-2-2

Tube racks

should also be cleaned daily by scrubbing them with a soft cloth and mild detergent,

followed by rinsing under water and drying carefully.

Refer to the Operating Manual for all routine general maintenance to perform as a part of
normal operation.

NOTE:

The CLINITEK?ATLAS?Rack Sample Handler MUST be balanced with a levelling
device to operate properly. Otherwise, rack jams may occur.

5-3

Preventative Maintenance

5-3-1

A field engineer on a service call on this system should do the following as part of the call:

1.

Verify

Transfer Plate

(see item 9 on page 10.36) and

racks

are clean.

2.

Verify the

Reflection Plate

(see item 2 on page 10.4) is clean and not scratched or loose.

3.

Verify

PH1-7 and PH9 sensor windows

are clean (see Figure 8-3 on page 8.4)

4.

Verify

Barcode Reader window

is clean (if instrument is using a barcode reader).

5.

Verify

waste tubing

is draining properly into the waste receptacle.

6.

Clean all covers with a soft, clean, damp cloth and mild detergent. Follow-up with a soft, clean,
damp cloth and dry carefully with a soft, clean cloth.

7.

Lastly, perform a With Tube Run in Service Mode for at least 30 minutes to verify system is
working properly.

Refer to the Preventative Maintenance Checklist on page 5.2.

See page 7.4 for more information about t

he Service Mode With Tube Run test.

For special preventative maintenance to be performed by a field engineer on the Clinitek
Atlas Analyzer, refer to the Clinitek Atlas Service Manual, part number 99A50018, Chapter
Five.

5-1

«
...
14
15
16
17
18
...
»

Содержание Clinitek Atlas


























































































































































































Отзывы:

Нет отзывов