Bayer HealthCare Clinitek Atlas Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 185

Bayer HealthCare Clinitek Atlas Скачать руководство пользователя страница 2

?998 Bayer Corporation

All Rights Reserved

Second Edition

June 1998

Company Confidential

Information contained herein is proprietary to Bayer Corporation and is classified company confidential. It is
furnished to Bayer Field Service Engineers for maintenance and overhaul of the subject equipment only. It
shall not be disclosed, duplicated, or used in whole or in part for any other purpose without the prior written
permission of Bayer Corporation.

Information contained in this service manual is designed for servicing of the CLINITEK?ATLAS?Rack Sample
Handler by qualified and properly trained service personnel using appropriate tools and test equipment. If you
do not possess the proper service tools and equipment and proper technical training, do not attempt to service
this instrument.

This service manual is kept current by service bulletins issued from the United States by Bayer Corporation,
Diagnostics Division. These bulletins are distributed world-wide to Bayer service personnel and others who
have received technical training from Bayer Diagnostics. Other possessors of this manual will not receive these
bulletins.

i

«
1
2
3
4
...
»

Содержание Clinitek Atlas


























































































































































































Отзывы:

Нет отзывов