Baumuller b maXX BMC-M-SAF-02 Скачать руководство пользователя | Manualshive

Страница: 31 / 120

background image

31

Operation Manual

b maXX safe PLC

BMC-M-SAF-02

Document no.: 5.07020.04

7

D

ESCRIPTION

OF

THE

B

MA

XX

SAFE

PLC

MODULE

This chapter describes the b maXX safe PLC module and the type code applied to the
module.

7.1

General

The b maXX safe PLC is an SPC for the implementation of central, hybrid and decentral
automation technology.

It primarily consists of the following components:

1

SW module for control and regulation programming (standard PLC)

2

SW module for programming safety applications (safety PLC)

The functions of the SPC, such as configurable control and regulation technology, digital
and analog inputs and outputs, connection to various bus systems as well as the control
and regulation of decentral drives (such as cam disk) via these bus systems (such as
EtherCAT) are implemented by means of the b maXX safe PLC and further system com-
ponents connected to it.

Safety applications can also be programmed in parallel to this. The safety core used for
this purposes is certified in accordance with SIL 3 (IEC61508).

The system can have both central and decentral I/O terminals. Standard data as well as
safe data can be transmitted via network components and the local I/O bus.

Safe drives which respond by means of safety protocols via bus systems are considered
to be I/O slaves in the system. The implementation of further safety functions such as
SS1, SS2 or SBC is carried out in the drives locally.

The safety programming is carried out by means of the ethernet activation communication
component group.

Control and regulation programming is carried out also by means of the same ethernet
activation system components. Alternatively, it can be programmed by means of the stan-
dard RS232 interface.

Also HMI interfaces (operator control panels, touch screens, etc.) can be connected by
means of this ethernet activation system. Alternatively, it can be connected to 3964R

®

procedure (data block connection) by means of the integrated RS485 interface, since the
3964R

®

procedure is assigned to the standard PLC and not to the safety PLC.

«
...
29
30
31
32
33
...
»

Содержание b maXX BMC-M-SAF-02

























































































































Отзывы:

Нет отзывов

Похожие инструкции для b maXX BMC-M-SAF-02

imageRUNNER ADVANCE C9075S PRO

Бренд: Canon Страницы: 20

Бренд: CAME Страницы: 32

Бренд: Babybee Prams Страницы: 21

Бренд: Gate Motors Страницы: 6

Бренд: IAI Страницы: 5

Бренд: JANE Страницы: 144

Бренд: Watlow Страницы: 4

Бренд: Madison AV Страницы: 2

Бренд: Insignia Страницы: 2

Бренд: Thermomart Страницы: 6

Бренд: Fuji Electric Страницы: 12

Бренд: heat-timer Страницы: 36

Бренд: Vertiv Страницы: 2

Бренд: Quantum Страницы: 20

LOWARA Aquavara IPC

Бренд: Xylem Страницы: 292

Бренд: Olsen Страницы: 4

Бренд: Water Specialist Страницы: 36

Бренд: Sunlover Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды