manualshive.com logo in svg

Baumuller b maXX BMC-M-SAF-02, Руководство по эксплуатации

Поделиться
Скачать
Baumuller b maXX BMC-M-SAF-02 Скачать руководство пользователя страница 50

Assembly instructions

Operation Manual 

b maXX safe PLC

 BMC-M-SAF-02

Document no.: 5.07020.04

Baumüller Nürnberg GmbH

50

of 118

9.5

1

Shut off the power to the power supply if necessary and make sure that it does not turn 
back on accidentally during the assembly work. Disconnect any already attached ca-
bles or lines from the connections

2

Open the electrical cabinet

3

Plug the b maXX safe PLC into the power supply

Figure 10:

b maXX safe PLC (BMC-M-SAF-02) with power supply

 

dual-channel safety PLC

If you are using additional system components for the b maXX safe PLC, plug them into 
the b maXX safe PLC from the left.

4

There is a white handle on the bottom of the left part of the power supply. Pull this han-
dle downward and then to the left. The handle will lock into place easily. 

 

Repeat this step with the b maXX safe PLC (3 handles with the BMC-M-SAF-02; 4 
handles with the BMC-M-SAF-02 with memory card module).

 

Repeat this step with any further system components for the b maXX safe PLC (which 
are plugged into the left side of the  maXX safe PLC).

BAUMULLER

H1

H4

H5

S1

SAF-02

S1

H1

H5

H9

H4

H8

H12

S2

012

34

5

7

6

89AB

C

D

E F

X1

X2

5

9

6

1

5

9

6

1

BAUMULLER

BAUMULLER

S1

H1

H4

BAUMULLER

PSB-02

S5

S4

S3

S2

012

34

5

7

6

89AB

C

D E

F

012

34

5

7

6

89AB

C

D E

F

0

0

1

1

2

2

3

3

4

4

5

5

7

7

6

6

8

8

9

9

A

A

B

B

C

C

D

D

E

E

F

F

24V

PE PE

+

- -

+

0V

H5

H8

NOTICE!

The b maXX system will not work if you plug the b maXX safe PLC into the another 
module of the b maXX system instead of plugging it into the power supply. 

The memory card module (CFI-01) is the only element which is allowed to be be-
tween the PLC and the power supply. The b maXX safe PLC requires the PSB-02 
power supply.

Содержание b maXX BMC-M-SAF-02

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды