manualshive.com logo in svg

Baroness GM2810, Руководство по обслуживанию

Поделиться
Скачать
Baroness GM2810 Скачать руководство пользователя страница 64

Caution

Before starting pressure measurement, make
sure that there are no people around the
machine.

Lower the mower units, and then remove the
hydraulic hose from the adapter attached to
the hydraulic cylinder.

1

2

3

4

z4kw7w-009

Up/Down circuit_002

1

Mower unit

2

Cylinder

3

Adapter

4

Hydraulic hose

Install the pressure gauge for high pressure
measurements between the removed hose
and adapter.

1

2

3

z4kw7w-010

Up/Down circuit_003

1

Hydraulic hose

2

Adapter

3

Pressure gauge for high pressure
measurements

1.

2.

Make sure that the parking brake is applied,
and then start the engine.

1

z4kw7w-011

Up/Down circuit_004

1

Mower unit

Rev the engine up to the maximum rpm.
The normal pressure is 13.7 MPa (1,986.95
psi) when the up/down lever is shifted to the
"UP" position and the up/down cylinder is
retracted to its maximum.
Items to Prepare for Measurement
Prepare a pressure gauge for high pressure
measurements, T-joint TEF1/4, 6 adapter,
and 6 hydraulic hose.

10

20

30

15

25

35

5

1

2

4

2

3

2

z4kw7w-043

Up/Down circuit_005

1

6 Hydraulic hose

2

6 Adapter

3

Pressure gauge for high pressure
measurements

4

T-joint TEF1/4

3.

4.

5.

GM2810

Hydraulic system

Page 4-36

Measurement

Содержание GM2810


























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды