manualshive.com logo in svg

Baroness GM2810, Руководство по обслуживанию

Поделиться
Скачать
Baroness GM2810 Скачать руководство пользователя страница 149

Remove the roller shaft.

1

6ehg7n-004

Inspection of Rear Roller_004

1

Roller shaft

Important

Be sure to replace the bearings, oil seals and
O-rings with new ones.

Have new bearings and oil seals ready, and
apply a profuse amount of grease.
Apply a profuse amount of grease to the lip
of the oil seal.

1

2

1lbr3a-008

Inspection of Rear Roller_005

1

Bearing

2

Oil seal

6.

7.

Caution

See the list in "Tightening torques" (Page
3-5) .
Note that the Baroness product warranty may
not apply to defects caused by incorrect or
overtorque tightening etc.

Install the rear roller ass'y following the
reversed procedure of the procedure 2 to 6.
Make sure that the roller has no play and
rotates smoothly when the roller shaft is
fixed and the roller is rotated.
Apply grease. (See "Greasing Points"
(Page 3-12) .)
Install the rear roller ass'y. (See "Installation
of Rear Roller Assy" (Page 7-12) .)

Mower Arm

Inspection of Mower Arm

Due to frequent use, or bends etc. caused by
damage during use or transportation, the
finish may not be smooth or the machine may
not cut properly. In this case, check the
mower arm and replace the parts, if
necessary.

Make sure that the bushing is not loose
inside the mower arm.
Check the tightening state of the attaching
portion with the mower frame.
Check if there is a change in shape etc. on
the mower arm.

Refer to ( "Removal of Mower Arm" (Page
7-14) ) and ( "Installation of Mower Arm"
(Page 7-15) ) for information on attaching and
removing the mower arm.

8.

9.

10.

11.

･

･

･

Operating Machine and Mower Units

GM2810

Operating Machine and Mower Units

Page 7-31

Inspection and repair of each section

Содержание GM2810


























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды