manualshive.com logo in svg

Baroness GM2810, Руководство по обслуживанию

Поделиться
Скачать
Baroness GM2810 Скачать руководство пользователя страница 128

Front Roller Assy

Removal of Front Roller Assembly

Danger

Danger

The rotary knife is an edged tool.
Handle it carefully, since it could cut your
hands or legs.

Caution

When touching edged tools, wear gloves,
since they could cut your hands.

Remove the mower units. (See "Removal of
Mower Unit" (Page 7-5) .)
Reverse the mower units.

1

2

kaatr1-001

Removal of Front Roller Assembly_001

1

Rotary knife

2

Mower unit

Remove the left and right nuts and washers
that are used to attach the front roller
assembly to the mower frame.

1

2

3

3

4

4

kaatr1-002

Removal of Front Roller Assembly_002

1

Mower frame

2

Front roller assembly

3

Nut

4

Washer

1.

2.

3.

Lift the front roller assembly and remove it
from the mower frame.

1

kaatr1-003

Removal of Front Roller Assembly_003

1

Front roller assembly

Follow the same procedure to remove the
front roller assembly on the opposite side.

4.

5.

GM2810

Operating Machine and Mower Units

Page 7-10

Removal and installation of each section

Содержание GM2810


























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды