manualshive.com logo in svg

Baroness GM2810, Руководство по обслуживанию

Поделиться
Скачать
Baroness GM2810 Скачать руководство пользователя страница 61

Items to Prepare for Measurement
Prepare a pressure gauge for high pressure
measurements, high pressure hose, and O-
ring connector PF1/4PF1/4.

1

2

3

g5t8is-035

Forward_005

1

Pressure gauge for high pressure
measurements

2

High pressure hose

3

O-ring connector PF1/4PF1/4

Reverse

Caution

Before starting pressure measurement, make
sure that there are no people around the
machine.

Remove the plug of the reverse side
measurement point of the 2WD/4WD
changeover valve located in the center
upper area of the pivot of the main unit.

1

2

7edlvx-034

Reverse_001

1

2WD/4WD changeover valve

2

Plug

6.

1.

Attach the O-ring connector to the reverse
side measuring port.

1

7edlvx-035

Reverse_002

1

O-ring connector (1096-6)

Attach the pressure gauge for high
pressure measurements onto the O-ring
connector of the reverse side measuring
port.

2

1

7edlvx-036

Reverse_003

1

Reverse side measuring port
connector

2

Pressure gauge for high pressure
measurements

2.

3.

Hydraulic system

GM2810

Hydraulic system

Page 4-33

Measurement

Содержание GM2810


























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды