manualshive.com logo in svg

Baroness GM2810, Руководство по обслуживанию

Поделиться
Скачать
Baroness GM2810 Скачать руководство пользователя страница 100

Solenoid Valve

Rotary Knife Rotation Valves

The rotary knife rotation valves are installed in
the lower right area behind the seat and in the
lower area in front of the seat.
Depending on the operation of the solenoid
valves, the hydraulic path in the rotary knife
rotation valve is switched to control the
rotation and stopping of the gear motors on
the mower units.

1

6i1yrf-003

Rotary Knife Rotation Valve_001

1

Solenoid valve

Inspection of Solenoid

Remove the connector of the solenoid.
It is normal if resistance between
connectors of the solenoid is about 10.9
Ω.

Solenoid Specifications

Voltage

Resistance

Holding

Current

DC 12 V

10.9 Ω

1.1 A

￭

1.
2.

￭

Diff-lock Valve

The diff-lock valve is located in the upper part
of the front axle.
Operation of the solenoid valves switches the
hydraulic path inside the diff-lock valve and
turns the diff-lock for the left and right front
wheels ON or OFF.

2

3

4

1

A

B

C

ehn1zf-001

Diff-lock Valve_001

1

Diff-lock valve

2

Solenoid #1

3

Solenoid #2

4

Solenoid #0

Inspection of Solenoid

Disconnect the solenoid connectors.
Measure the resistance between the
connector terminals of the solenoid. The
normal operation is when the measured
values are as in the table.

Solenoid Specifications

Solenoid

Number

Voltage

Resistance

Holding

Current

#0

DC12 V

4.5 Ω

2.6 A

#1

・

#2

DC12 V

7.2 Ω

1.67 A

￭

1.
2.

￭

GM2810

Electrical system

Page 5-18

Electrical components

Содержание GM2810


























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды