Baroness GM1700 Скачать руководство пользователя страница 175

Страница: 175 / 192

Relating to Traveling

Problem

Cause

Reference

Traveling power is poor.

Engine rpm is slow.

This machine's Owner's
Operating Manual

Engine does not run smoothly

Engine Maintenance
Manual

The parking brake is applied.

This machine's Owner's
Operating Manual

The piston pump speed change lever does not
shift enough.

Main body - Adjustment -
Traveling rod - Adjustment
of traveling rod

The unload valve is not completely closed.

This machine's Owner's
Operating Manual

Amount of hydraulic oil is low.

This machine's Owner's
Operating Manual

Blockage of hydraulic oil line filter

This machine's Owner's
Operating Manual

Hydraulic oil is too cool.

This machine's Owner's
Operating Manual

Dirt in the hydraulic oil (contamination, invasion of
water, air)

This machine's Owner's
Operating Manual

Viscosity of the hydraulic oil is wrong.

This machine's Owner's
Operating Manual

Pressure of the piston pump is not high enough.

Replacement of the piston
pump

Malfunction of the piston pump

Replacement of the piston
pump

Malfunction of the wheel motor

Replacement of the wheel
motor

It does not travel (in the case
where the aforementioned causes
do not exist).

Malfunction of linkage, etc. from the traveling
pedal to the pump

Main body - Adjustment -
Traveling rod - Adjustment
of traveling rod

The unload valve is open.

This machine's Owner's
Operating Manual

The piston pump speed change lever does not
operate.

Main body - Adjustment -
Traveling rod - Adjustment
of traveling rod

There is no charge pressure of the piston pump.

Hydraulic system -
Measurement - Charge
circuit

Malfunction of the joint part between the engine
and pump

Inspection, repair, or
replacement of the joint
part

2WD/4WD changeover does not
work.

Malfunction of the 2WD/4WD changeover lever

Inspection and replacement
of the lever and rod

Malfunction of the 2WD/4WD changeover valve

Replacement of the
2WD/4WD changeover
valve

Troubleshooting

GM1700

Troubleshooting

Page 8-5

Relating to Traveling

Содержание GM1700

































































































































































































Результаты поиска

Содержание GM1700

Отзывы:

Похожие инструкции для GM1700

Бренды по названию

Популярные бренды

Baroness GM1700, Руководство по обслуживанию

Результаты поиска

Содержание GM1700

Отзывы:

Похожие инструкции для GM1700

Бренды по названию

Популярные бренды