Baroness GM1700 Скачать руководство пользователя | Manualshive

Страница: 121 / 192

background image

Adjustment

Adjustment of Cutting Height

Cutting Height Table

Important

Adjust all mower units to the same cutting
height.

The adjustment range for the cutting height
is 35 - 95 mm (15 mm spacing, 5 levels).

Left/Right

Decks

Cutting Height

(mm)

Center Deck

A-C

95

e

B-D

80

d

A-D

65

c

B-E

50

b

A-E

35

a

䌅

䌁
䌂
䌃
䌄

䌡

䌢

䌣

䌤

䌥

1

2

yizobu-002

Cutting Height Table_001

1

Left/right decks

2

Center deck

Attach the cutting height adjustment label to
the mower unit.

1

yizobu-003

Cutting Height Table_002

1

Cutting height adjustment label

￭

GM1700-2161Z0
Contour deck cutting height adjustment
label

䌅

䌁
䌂
䌃
䌄

䋳䋵

䋵䋰

䋶䋵

䋸䋰

䋹䋵

䌁䇭䋭䇭䌃

䌂䇭䋭䇭䌄

䌁䇭䋭䇭䌄

䌂䇭䋭䇭䌅

䌁䇭䋭䇭䌅

䌣

䌡

䌢

䌣

䌤

䌥

䌢

䌡

䌤

䌥

yizobu-004

Cutting Height Table_003

Adjustment of Center Deck

The cutting height of the center deck is
adjusted with the cutting height gauge
wheels mounted at the front and back of
the deck.
There are four cutting height gauge wheels.

Important

The length of grass cut off at any one time
must be no more than 30 mm.

Important

Do not cut off more than 1/3 of the grass
height.

Apply the parking brake, and then raise
the mower unit so that the cutting height
gauge wheels do not touch the ground.
Stop the engine, and then remove the
key.
Loosen the bolt and nut on the cutting
height gauge wheel at the front of the
deck.

1

3

2

tlpgbi-001

Adjustment of Center Deck_001

1.

2.

3.

Operating Machine and Mower Units

GM1700

Operating Machine and Mower Units

Page 7-5

Contour Deck

«
...
119
120
121
122
123
...
»

Содержание GM1700

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GM1700

Бренд: MTD Страницы: 9

Бренд: ZIPPER MASCHINEN Страницы: 65

Бренд: P.Lindberg Страницы: 36

Бренд: Toro Страницы: 72

Ultra Vac QDS Frontrunner FRCK524

Бренд: Exmark Страницы: 7

DECK PARK 107 M HD EL - 4WD

Бренд: Stiga Страницы: 2

Бренд: Alamo Страницы: 104

Бренд: Kubota Страницы: 143

GF1800 ROPS Cab

Бренд: Kubota Страницы: 19

Бренд: FXA Страницы: 65

Бренд: FUXTEC Страницы: 18

Бренд: FUXTEC Страницы: 51

Бренд: Eastman Industries Страницы: 23

Бренд: Texas Equipment Страницы: 10

Бренд: sunjoe Страницы: 16

Бренд: Task Force Страницы: 11

Бренд: ATIKA Страницы: 116

Бренд: Toro Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды