B&R 8I84T200037.01P-1, Руководство пользователя

Страница: 271 / 405

Programming guidelines
ACOPOSinverter P84 User's Manual 2.10 271
[PARAM. SET SWITCHING] (MLP-)
Code Name/Description Factory settings
MLP- [PARAM. SET SWITCHING]
CHA1 [2 parameter sets] [No] (nO)
nO [No] (nO) : Function not active.
FtA [Thresh. Freq. err.] (FtA) : Switching via [F.-Thresh. Mot] (Ftd) )
F2A
[Thresh. Freq. 2 err.]
(F2A) : Switching via
[F.-Thresh. 2]
(F2d) )
LI1 [LI1] (LI1)
- .
[...] (...) : See the assignment conditions
Switching 2 parameter sets
CHA2 [3 parameter sets] [No] (nO)
nO [No] (nO) : Function not active.
FtA [Thresh. Freq. err.] (FtA) : Switching via [F.-Thresh. Mot] (Ftd) .
F2A [Thresh. Freq. 2 err.] (F2A) : Switching via [F.-Thresh. 2] (F2d) )
LI1 [LI1] (LI1)
- .
[...] (...) : See the assignment conditions
Switching 3 parameter sets
Note:
To obtain 3 parameter sets, [2 param. sets] must also be configured.
[PARAMETER SELECTION]
This parameter is only accessible on the graphic display terminal if [2 param. sets] is not at [No] (nO) .
Making an entry in this parameter opens a window containing all the adjustment parameters that can be accessed.
Select 1 to 15 parameters with the ENT key (a check mark appears by your selections) or cancel the parameter selection with ESC.
Example:
- - - - - - - - -
- - - - - - - - -
- - - - - - - - -
Ramp increment
SELECTED PARAMETERS
1.3 SETTINGS
PS1- [SET 1]
The parameter is accessible if at least 1 parameter in the [SELECTED. PARAMETERS] has been selected.
Making an entry in this parameter opens a settings window containing the selected parameters in the order in which they were selected .
With the graphic display terminal:
RDY Term +0.00 Hz 0 A
Start up:
<< >>
Quick
ENT
Startup time
9.51 s
Min = 0.1 Max = 999.9
9.67 s
12.58 s
13.45 s
2.3 s
9.51 s
RDY Term +0.00 Hz 0 A
SET1
Start up:
Deceleration:
Acceleration 2:
Code
<< >>
Quick
Deceleration 2:
Begin Acc round:
With integrated display terminal:
Proceed as in the Settings menu using the parameters that appear.
PS2- [SET 2]
The parameter is accessible if at least 1 parameter in the
[SELECTED. PARAMETERS]
has been selected.
Procedure identical to [PARAMETER SET 1] (PS1-) .
PS3- [SET 3]
The parameter is accessible if [3 parameter set] is not [No] (nO) and if at least 1 parameter has been selected in [SELECT. PARAMETER] .
Procedure identical to [PARAMETER SET 1] (PS1-) .
Note:
We recommend that a parameter set switching test is carried out while stopped and a check is made
to ensure that it has been performed correctly. Some parameters are interdependent and in this case
may be restricted at the time of switching.
The mutual dependency of parameters must be taken into account, even between different sets.
Example: The highest
[low frequency] (LSP) must be lower than the lowest [high frequency] (HSP) .