B&R 8I84T200037.01P-1, Руководство пользователя

Страница: 183 / 405

Programming guidelines
ACOPOSinverter P84 User's Manual 2.10 183
Alarms can be classified into 1 to 3 groups with the following submenus. Each of these groups can be assigned a
relay or logic output to the distributed signals. These groups can also be retrieved on the graphic display terminal
(see menu [SELECT DISPLAY TYPE] ) and via the menu [MONITOR] (SUP) .
If one or more of the alarms in a group of selected alarms occur, this alarm group is enabled.
[ERROR ALARM GR. 1] (A1C-) , [ERROR ALARM GR. 2] (A2C-) , [ERROR ALARM GR. 3] (A3C-)
Code Name/Description
A1C- [ALARM GRP1 DEFINITION]
A selection must be made from the following list:
PLA [Al. LI6=PTC] (PLA) : Alarm PTC sensor LI6=PTC
P1A [Alarm PTC1] (P1A) : Alarm PTC sensor 1
P2A [Alarm PTC2] (P2A) : Alarm PTC sensor 2
EFA [Al ext fault] (EFA) : Alarm external fault
USA [Undervoltage] (USA) : Alarm for an undervoltage
AnA
[Al haul err.]
(AnA) : Alarm for a hauling error
CtA [Thresh. I err.] (CtA) : Current threshold value reached ( [current threshold] (Ctd) )
FtA [Thresh. Freq. err.] (FtA) : Frequency threshold is reached ( [F.-Thresh. Mot] (Ftd) )
F2A [Thresh. Freq. 2 err.] (F2A) : Threshold frequency reached [Thresh. freq. 2] (F2d) )
SrA [FRH err.] (SrA) : Frequency reference reached
tSA [Th Status Motor err] (tSA) : Motor thermal state 1 reached
tS2 [Th Status Motor 2 err] (tS2) : Motor thermal state 2 reached
tS3 [Th Status Motor 3 err] (tS3) : Motor thermal state 3 reached
UPA [Voral. UVF] (UPA) : Prevention of undervoltage
FLA [HSP err.] (FLA) : High frequency attained
tHA
[Al. °C ATV]
(tHA) : Drive overheating
bSA [Al brake haul err] (bSA) : Alarm speed during braking
bCA [AI Brcont] (bCA) : Alarm feedback brake contact
PEE [PID error alarm] (PEE) : PID controller error alarm
PFA [Al. PID feedb.] (PFA) : Alarm PID feedback
AP2 [AI2 Al. 4-20] (AP2) : Alarm 4-20 mA signal at AI2 input not available
SSA [Limt T/I err] (SSA) : Alarm torque limiting
tAd [Th FU err] (tAd) : Thermal state of the inverter is reached
tJA [Alarm IGBT] (tJA) : Alarm IGBT
rtA [Al. T. contr.] (rtA) : Alarm torque control
bOA
[AI. brake res.]
(bOA) : Alarm temperature of the braking resistor
APA [Al. Option] (APA) : Alarm generated by an option card
UrA [Alarm USF cons.] (UrA) : Reserved
rSdA [Rope spg al.] (rSdA) : Slack rope (see parameter [Config. slack rope] (rSd) )
ttHA [Alarm high torque] (ttHA) : Motor torque exceeds upper threshold [Torque thd. high] (ttH)
ttLA [Alarm low torque] (ttLA) : Motor torque below lower threshold [Torque thd. low] (ttL)
dLdA [Alarm load variation] (dLdA) : Detection of a load deviation (see [DET. DELTA LOAD] (dLd-) ).
Refer to the procedure for multiple selection
A2C- [ALARM GRP2 DEFINITION]
Identical to [ERROR ALARM GR. 1] (A1C-)
A3C-
[ALARM GRP3 DEFINITION]
Identical to [ERROR ALARM GR. 1] (A1C-)