Bandit 3400T Скачать руководство пользователя

Страница: 10 / 56

Bandit

PAGE 10

MODEL 3400T

SAFETY PROCEDURES

Do not attempt to operate the track machine on an ascending or descending slope of more than 25° or 46%

or a side slope of more than 17° or 30%, it is Dangerous and could be Fatal. This is the maximum slope grade

the machine can be operated on if the hydraulics, tracks, and engine are running at maximum performance and

the tracks sustain good traction.

The track machine should never be parked on a slope at any time. The machine can coast or creep causing

equipment and/or personal injury.

DANGER

Make sure everyone is clear of machine before moving the track machine. Stay clear of tracks when the

machine is moving.

DANGER

DO NOT

entangle feet or hands in undercarriage travel system.

DANGER

NEVER sit, stand, lay, climb or ride anywhere on this machine while it is running, operating, or in transit. You

will be injured.

DANGER

Use

EXTREME CAUTION

when traveling over non-level surface! This machine can tip over or tip backwards

on non-level surface. You will cause engine damage, machine damage and possible personal injury!

DANGER

WARNING

Any increase from the specified maximum operating angles may cause loss of lubrication function and damage

the engine.

WARNING

Maximum Slope Grade

Diagram shows percentage to degree of slope.

Percentage is in vertical feet for every 100 horizontal feet.

Ascending or Descending Slope

Side Slope

IF MACHINE IS EQUIPPED WITH UNDERCARRIAGE TRACK

Machines equipped with undercarriage tracks are shipped with a manual from the track manufacturer. Refer

to it for service, operation, and safety information.

Содержание 3400T

























































Результаты поиска

Содержание 3400T

Отзывы:

Похожие инструкции для 3400T

Бренды по названию

Популярные бренды

Bandit 3400T, Руководство пользователя

Результаты поиска

Содержание 3400T

Отзывы:

Похожие инструкции для 3400T

Бренды по названию

Популярные бренды