Bandit 3400T Скачать руководство пользователя

Страница: 49 / 56

Bandit

PAGE 9

MODEL 3400T

FRAME COMPONENTS

LOCATION PART NUMBER

DESCRIPTION

99-00116

Front Inspection Cover

99-0011

Top Inspection Cover

900-2907-52

Back-Up Beeper

See Page

Remote Control Antenna

900-91-97

Split Bushing

900-9-07

Swing Cylinder Pin

7 a.

Right & Left Track Assembly (Set)

Replacement Track Only

994-300221

Rubber Mounting Pad For Hydraulic Tank

900-9-60

Magnetic Drain Plug

10.

900-91-1

1 1/” Suction Screen

11.

900-3920-14

1 1/2” Shut-Off Valve

12.

900-3907-77

1” Shut-Off Valve

900-901-

1” Suction Screen

900-901-78

Temperature/Sight Gauge

15.

994-200020

Hydraulic Tank Assembly

16.

900-3925-91

Fill Cap - Hydraulic Tank

17 a.

993-300399

Fill Cap Lock Assembly - Hydraulic Tank

900-4912-40

Padlock With Short Shackle For Tank With Locking Cap (Not Shown)

P812

Key For Padlock (Not Shown)

18.

900-9-97

Return Filter

19.

900-97-

Filter Head

989-00911

Clean Out Door

21.

994-300133

Deck Plate

99-0016

Rubber Engine Isolator

23 a.

900-4901-83

Spring Lock - 1/2” Diameter Pin

900-7900-9

Rubber Cap (Not Shown)

99-0007

Oil Cooler Mount Assembly

25 a.

994-200035

Tool Box Assembly (Start W/O 36836)

994-100016

Tool Box Assembly (Pre W/O 36429)

900-9904-33

Tool Box Handle Only

900-6900-0

660 CCA Battery

99-0008

Battery Hold Down Strap

28.

994-100011

Control Box Assembly

29 a.

900-2911-54

Tether Jack

900-2911-55

Cap For Tether Jack

0 a.

900-90-8

“T” Latch Handle

Key

31.

See Page 53

Receiver Circuit Board Box

900-990-07

Manual Holder

33.

994-300225

Rubber Mounting Pad For Fuel Tank

900-90-1

Rochester Sight Gauge

35.

900-3917-71

Fill Cap - Fuel Tank

36 a.

980-0506-86

Fill Cap Lock Assembly - Fuel Tank

900-4912-40

Padlock With Short Shackle For Tank With Locking Cap (Not Shown)

P812

Key For Padlock (Not Shown)

7 a.

900-96-86

Drop Pipe Assembly For Suction Line

900-91-

Hose Barb For Suction Line

38.

900-3931-36

Vent Elbow With Hose Barb

9 a.

900-910-

Drop Pipe Assembly For Return Line

900-909-0

Hose Barb For Return Line

40.

994-100010

Fuel Tank Assembly

NOTE: **

Components need to be ordered by serial number of machine.

Содержание 3400T

























































Результаты поиска

Содержание 3400T

Отзывы:

Похожие инструкции для 3400T

Бренды по названию

Популярные бренды

Bandit 3400T, Руководство пользователя

Результаты поиска

Содержание 3400T

Отзывы:

Похожие инструкции для 3400T

Бренды по названию

Популярные бренды