Baldor Flex+DriveII Скачать руководство пользователя страница 99

Страница: 99 / 126

Accessories A-1

MN1902

A.1 Introduction

This section describes accessories and options that you may need to use with your
FlexDrive

. Shielded (screened) cables provide EMI / RFI shielding and are required for

compliance with CE regulations. All connectors and other components must be compatible
with the shielded cable.

A.1.1 Factory fitted options

The FlexDrive

can be supplied with a number of factory fitted options. Each option is

described in a separate manual that will be supplied with your product as necessary:

MN1908 -

CAN & Auxiliary I/O Option for Flex+Drive

and MintDrive

Option B provides CANopen and additional input / output capabilities. If this option is fitted,
the Flex+Drive

front panel will include connectors X10, X11 and X12.

MN1909 -

CAN Option for FlexDrive

, Flex+Drive

and MintDrive

Option C provides CANopen capabilities. If this option is fitted, the FlexDrive

front panel

will include connectors X10 and X11.

MN1910 -

DeviceNet Option for FlexDrive

, Flex+Drive

and MintDrive

Option D provides DeviceNet capabilities. If this option is fitted, the FlexDrive

front panel

will include connector X15.

MN1911 -

PROFIBUS DP Option for FlexDrive

, Flex+Drive

and MintDrive

Option P provides Profibus capabilities. If this option is fitted, the FlexDrive

front panel

will include connector X14.

Accessories

Содержание Flex+DriveII































































































































Результаты поиска

Содержание Flex+DriveII

Отзывы:

Похожие инструкции для Flex+DriveII

Бренды по названию

Популярные бренды

Baldor Flex+DriveII, Руководство по установке

Результаты поиска

Содержание Flex+DriveII

Отзывы:

Похожие инструкции для Flex+DriveII

Бренды по названию

Популярные бренды