Baldor Flex+DriveII Скачать руководство пользователя страница 34

Страница: 34 / 126

3-20 Basic Installation

MN1902

3.6 Regeneration resistor (Dynamic Brake resistor)

The 2.5A and 5A FlexDrive

both have an internally fitted regeneration resistor *. For 7.5A,

15A, 20A and 27.5A FlexDrive

, an external regeneration resistor must be installed to

dissipate excess power from the internal DC bus during motor deceleration.

Suitable regeneration resistors are listed in section A.1.7.

WARNING

: A regeneration resistor may generate enough heat to

ignite combustible materials. To avoid fire hazard,
keep all combustible materials and flammable vapors
away from the resistors.

The regeneration resistor should be mounted near the top of an enclosure
to maximize heat dissipation. When the motor regenerates, the yellow

DB On

LED on the front panel of the FlexDrive

will illuminate.

* If required by the application, additional external resistors connected to R1 and R2 will be

connected in parallel with the internal resistor.

3.6.1 Controlling regeneration

Some regeneration resistor assemblies include an overload switch to indicate when too much
power is being dissipated by the resistor. This switch can be wired to a digital input on the
FlexDrive

. Using the WorkBench v5 Digital I/O tool, the input can be configured to be the

brake trip input. This allows the FlexDrive

to respond to resistor overload conditions.

The Mint keyword

DBEXTTRIPINPUT

can also be used to configure a digital input for this

purpose. On three-phase FlexDrive

models, the operation of the regeneration resistor can be

controlled by further Mint keywords. These also begin with the letters

..., for example

DBEXTPEAKPOWER

. See the Mint help file for details.

R1
R2

Содержание Flex+DriveII































































































































Результаты поиска

Содержание Flex+DriveII

Отзывы:

Baldor Flex+DriveII, Руководство по установке, Страница: 34 / 126

Результаты поиска

Содержание Flex+DriveII

Отзывы: