Baldor Flex+DriveII Скачать руководство пользователя страница 47

Страница: 47 / 126

Basic Installation 3-33

MN1902

3.9.6 Switches 9 and 10 - RS232/RS485 select

Switch 9 is reserved for Baldor keypad selection.

Switch 10 selects RS232 communications (Off) or RS485/RS422 (On) the next time the
FlexDrive

is power-cycled.

3.9.7 Factory settings

If switches 1-4 are all in the On position and switch 8 is set to Off, the FlexDrive

will be reset

to its preset factory settings at power on (or whenever the processor is reset by
WorkBench v5).

CAUTION

: Use this function carefully - it will erase your drive setup information.

When using the SW1 DIP switches to reset the FlexDrive

to its factory defaults, all

parameters including the node number and serial communications baud rate will be reset.
In WorkBench v5, this means it will be necessary to rescan for the FlexDrive

(by starting a

new project) to enable communication. It will also be necessary to re-tune your motor and
drive.

Reapply

power.

FlexDrive

will

be reset to its

preset factory

settings.

Off

Remove

power.

Figure 20 - Resetting the FlexDrive

to its factory default settings

The Mint keyword

FACTORYDEFAULTS

can also be used to reset the FlexDrive

to its factory

defaults. However, it will not reset the node number or serial communications baud rate. See
the Mint help file for details.

Содержание Flex+DriveII































































































































Результаты поиска

Содержание Flex+DriveII

Отзывы:

Похожие инструкции для Flex+DriveII

Бренды по названию

Популярные бренды

Baldor Flex+DriveII, Руководство по установке

Результаты поиска

Содержание Flex+DriveII

Отзывы:

Похожие инструкции для Flex+DriveII

Бренды по названию

Популярные бренды