Baldor Flex+DriveII Скачать руководство пользователя | Manualshive

Страница: 115 / 126

background image

CE Guidelines C-1

MN1902

C.1 Outline

This section provides general information
regarding recommended methods of installation
for CE compliance. It is not intended as an
exhaustive guide to good practice and wiring
techniques. It is assumed that the installer of the
FlexDrive

II

is sufficiently qualified to perform the

task, and is aware of local regulations and
requirements. Baldor products that meet the
EMC directive requirements are indicated with a
“CE” mark. A duly signed CE declaration of
conformity is available from Baldor.

C.1.1 EMC Conformity and CE marking

The information contained herein is for your guidance only and does not guarantee that the
installation will meet the requirements of the council directive 89/336/EEC.

The purpose of the EEC directives is to state a minimum technical requirement common to all
the member states within the European Union. In turn, these minimum technical requirements
are intended to enhance the levels of safety both directly and indirectly.

Council directive 89/336/EEC relating to Electro Magnetic Compliance (EMC) indicates that it
is the responsibility of the system integrator to ensure that the entire system complies with all
relative directives at the time of installing into service.

Motors and controls are used as components of a system, per the EMC directive. Hence all
components, installation of the components, interconnection between components, and
shielding and grounding of the system as a whole determines EMC compliance.

The CE mark informs the purchaser that the equipment has been tested and complies with the
appropriate standards. It rests upon the manufacturer or his authorized representative to
ensure the item in question complies fully with all the relative directives in force at the time of
installing into service, in the same way as the system integrator previously mentioned.
Remember that it is the instructions of installation and the product that should comply with the
directive.

C

CE Guidelines

C

«
...
113
114
115
116
117
...
»

Содержание Flex+DriveII































































































































Отзывы:

Нет отзывов

Похожие инструкции для Flex+DriveII

Бренд: Bardac Страницы: 62

PowerXL DM1 Series

Бренд: Eaton Страницы: 28

Бренд: Eaton Страницы: 5

Бренд: Eaton Страницы: 240

Бренд: Eaton Страницы: 34

Бренд: Eaton Страницы: 179

Бренд: Eaton Страницы: 46

PowerXL DG1 Series VFD

Бренд: Eaton Страницы: 24

PowerXL DG1 Series VFD

Бренд: Eaton Страницы: 152

Бренд: Eaton Страницы: 18

Бренд: Eaton Страницы: 58

Бренд: Eaton Страницы: 20

Бренд: Eaton Страницы: 195

Cutler-Hammer SLX9000 Series

Бренд: Eaton Страницы: 24

PowerXL DM1 Series

Бренд: Eaton Страницы: 68

HELICAL GEAR BOXES BC Series

Бренд: BOCKWOLDT Страницы: 70

Бренд: Kalatec Automacao Страницы: 24

TWIN MASTER 24V

Бренд: UCS Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды