Baldor Flex+DriveII Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 126

background image

3-30 Basic Installation

MN1902

3.8.2 Drive enable - SW1 DIP switch

To enable the FlexDrive

II

the front panel DIP switch 8 must be set to On.

This switch provides a local enable/disable switch that can be useful
during testing.

The state of the drive enable DIP switch is displayed in the WorkBench v5
Spy window. It can also be checked (but not set) using the Mint keyword

ENABLESWITCH

. See the Mint help file for details.

See section 3.9 for full details of other DIP switch functions.

3.8.3 Drive enable command

The other action required to enable the FlexDrive

II

can be controlled either by software or

hardware.

Note:

This method is explained here for your information, but cannot be completed until
you have installed the software and are ready to turn on AC power to the drive.
Please continue to read all sections in sequence. Do not turn on AC power until
you reach the appropriate instructions.

In software, a drive enable command must be issued. The easiest way to do this is by clicking
the Drive enable button

in WorkBench v5. Alternatively, the Mint commands

RESET

or

DRIVEENABLE=1

can be used. See the Mint help file for details.

In hardware, a digital input can be used to create the drive enable command. This can be
configured in WorkBench v5 using the Digital inputs tab of the Digital I/O tool. Alternatively, the
Mint keyword

RESETINPUT

can be used to select the required digital input. See the Mint help

file for details.

Another method is to use the Mint keyword

DRIVEENABLEMODE

. This allows the combination

of DIP switch 8 and the Enable input to create the drive enable command. Both inputs must
become active. Provided one input is already on, as soon as the other input changes from off
to on (active), the drive will be enabled. See the Mint help file for details.

On

8

«
...
42
43
44
45
46
...
»

Содержание Flex+DriveII































































































































Отзывы:

Нет отзывов

Похожие инструкции для Flex+DriveII

Бренд: National Instruments Страницы: 29

Бренд: Tandon Страницы: 105

Бренд: Lamtec Страницы: 40

Бренд: Daikin Страницы: 39

Бренд: Vacon Страницы: 82

Бренд: EKSMA OPTICS Страницы: 12

Бренд: Siemens Страницы: 168

Бренд: Siemens Страницы: 186

Sinamics GM150 6SL3835-2LN44-2AA0

Бренд: Siemens Страницы: 238

SINAMICS PM240-2

Бренд: Siemens Страницы: 144

Бренд: Siemens Страницы: 520

SINAMICS PERFECT HARMONY GH180

Бренд: Siemens Страницы: 538

Бренд: Siemens Страницы: 680

Бренд: Siemens Страницы: 1288

Бренд: TELUS Страницы: 49

Бренд: Shihlin electric Страницы: 555

Бренд: Becker Страницы: 20

Бренд: STG-BEIKIRCH Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды