Baldor Flex+DriveII Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 126

background image

4-16 Input / Output

MN1902

4.4.5 Multidrop using RS485 / RS422 cable

Multidrop systems allow one device to act as a ‘network master’, controlling and interacting
with the other (slave) devices on the network. The network master can be a controller such as
a FlexDrive

II

, a host application such as WorkBench v5 (or other custom application), or a

programmable logic controller (PLC). RS422 may be used for multi-drop applications as
shown in Figure 34. Four-wire RS485 may be used for single point-to-point applications
involving only one Baldor controller. If firmware is updated over RS485/RS422, it can only be
downloaded to the drive that was chosen in the Select Controller dialog in WorkBench v5.

Network slave

T

R

RX-

DGND

RX+

TX+

TX-

RX-

DGND

RX+

TX+

TX-

RX-

DGND

RX+

TX+

TX-

Twisted pairs

T

R

Connect overall shield
to connector backshell.

Network slave

Network

master

Master and final slave are

shown with terminating

resistors, T

R

, typical value

120

Ω

.

Front panel DIP switch 6 may

be used to connect an internal

120

Ω

terminating resistor

.

Figure 34 - 4-wire RS422 multi-drop connections

Any FlexDrive

II

on the network must have its SW1 DIP switch 10 (located

on the front panel) set to the On position (see also section 3.9.6). This will
set the serial port to RS422/RS485 mode after the next power off/on cycle.
When SW1 DIP switch 6 is set to the On position, a 120

Ω

termination

resistor is connected between the RX+ and RX- signals.

Each TX/RX network requires a termination resistor at the final RX
connection, but intermediate devices must not be fitted with termination
resistors. An exception is where repeaters are being used which may

correctly contain termination resistors. Termination resistors are used to match the impedance
of the load to the impedance of the transmission line (cable) being used. Unmatched
impedance causes the transmitted signal to not be fully absorbed by the load. This causes a
portion of the signal to be reflected back into the transmission line as noise. If the source
impedance, transmission line impedance, and load impedance are all equal, the reflections
(noise) are eliminated. Termination resistors increase the load current and sometimes change
the bias requirements and increase the complexity of the system.

On

10

On

6

«
...
62
63
64
65
66
...
»

Содержание Flex+DriveII































































































































Отзывы:

Нет отзывов

Похожие инструкции для Flex+DriveII

Бренд: Fagor Страницы: 56

Бренд: Leroy-Somer Страницы: 60

Бренд: YASKAWA Страницы: 50

Бренд: Eaton Страницы: 96

Бренд: INGENIA Страницы: 124

Бренд: Bosch Страницы: 50

Бренд: Bosch Страницы: 66

rexroth Servodyn-D

Бренд: Bosch Страницы: 72

MSK030B NSNN Series

Бренд: Bosch Страницы: 178

MSK030B-0900-NN

Бренд: Bosch Страницы: 282

Бренд: Pro-dig Страницы: 26

Бренд: KB Electronics Страницы: 44

Vivid Drive 23N

Бренд: Chauvet DJ Страницы: 56

Бренд: RS Automation Страницы: 332

Transmate 371-00

Бренд: Romac Страницы: 4

Бренд: BLUM Страницы: 20

Бренд: Baumuller Страницы: 80

Бренд: Wheeler-Rex Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды