Baldor Flex+DriveII Скачать руководство пользователя | Manualshive

Страница: 83 / 126

background image

Troubleshooting 6-3

MN1902

(Symbol not flashing)
Motor I

2

T / It foldback. Motor I

2

T or Drive I.T algorithm has resulted in the demand

current being folded back to a level where the drive/motor can recover. The motor /
drive can run with demand currents greater than their rated value for a period of time;
after that time the drive will either trip or automatically foldback the demand current.

Overtemperature. The temperature of the drive or motor has exceeded a trip level (see
Mint keyword

TEMPERATURELIMITFATAL

) or the Motor overtemperature trip input

has been activated (see Mint keyword

MOTORTEMPERATUREINPUT

).

Drive enabled. The drive is enabled (except where

CONFIG = _cfVirtual

, where it

is not physically enabled).

Torque mode. The drive is in Torque mode. See the Mint keywords

TORQUE

,

TORQUEREFSOURCE

and related commands.

Auto tune test driving motor. Autotune is active and driving the motor. The motor may
move.

Power base not ready. This error condition applies to 3-phase drives only. These drives
have a pre-charge circuit which must activate after power-up before the drive can be
enabled. If the drive is enabled prior to this then the error occurs. The error could also
indicate the loss of one or more of the input phases.

Cam. A Cam profile is being profiled. See the Mint keyword

CAM

.

General error. See

AXISERROR

and

DRIVEERROR

. The motion toolbar displays the

status of

AXISERROR

, which is a bit pattern of all latched errors. See also the

Error Log

topics in the help file.

Error input. The

ERRORINPUT

has been activated and generated an error.

Flying shear. A flying shear is being profiled. See the Mint keyword

FLY

.

Position or velocity following error. A following error has occurred. See the Mint
keyword

AXISERROR

and associated keywords. Following errors could be caused by a

badly tuned drive/motor. At higher acceleration and deceleration rates, the following
error will typically be greater. Ensure that the drive/motor is adequately tuned to cope
with these acceleration rates.
The following error limit can be adjusted to suite your application (see Mint keywords

FOLERRORFATAL

and

VELFATAL

). Following error could also be the cause of

encoder/resolver loss (see also Mint keyword

FEEDBACKFAULTENABLE

).

Follow mode. The drive is in Follow mode. See the Mint keyword

FOLLOW

.

Hold. The Hold DIP switch is active (see section 3.9.2) or the PLC Task has requested
a Hold state. Motion will be ramped to zero demand and will then hold on position while
the switch is active.

Homing. The drive is currently homing. See the Mint keyword

HOME

.

Preset Homing. The drive is currently homing. This motion has been triggered from a
Preset move table.

«
...
81
82
83
84
85
...
»

Содержание Flex+DriveII































































































































Отзывы:

Нет отзывов

Похожие инструкции для Flex+DriveII

Бренд: GFA Страницы: 24

Бренд: Yale Страницы: 14

Бренд: Aumuller Страницы: 48

Бренд: Raymarine Страницы: 23

Бренд: Ace Страницы: 2

MILLENIUM 1100-46D

Бренд: York Страницы: 24

Бренд: CENTENT Страницы: 48

Бренд: Berger Lahr Страницы: 45

AC Tech PositionServo 940

Бренд: Lenze Страницы: 75

Бренд: Becker Страницы: 64

Бренд: Lenze Страницы: 189

Danaher Motion P70360

Бренд: Pacific Scientific Страницы: 18

Бренд: Melec Страницы: 39

CIMR-AC4A0103TAA

Бренд: YASKAWA Страницы: 40

Бренд: ABB Страницы: 20

Бренд: ZGC Страницы: 30

Бренд: MAIMAN ELECTRONICS Страницы: 20

Бренд: Danfoss Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды