Baldor Flex+DriveII Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 126

background image

1-4 General Information

MN1902

CAUTION

: Avoid locating the drive in the vicinity of corrosive substances or vapors, metal

particles and dust.

CAUTION

: Do not connect AC power to the drive terminals U, V and W. Connecting AC

power to these terminals may result in damage to the drive.

CAUTION

: Baldor does not recommend using “Grounded Leg Delta” transformer power leads

that may create earth/ground loops and degrade system performance. Instead,
we recommend using a four wire Wye.

CAUTION

: Drives are intended to be connected to a permanent main power source, not a

portable power source. Suitable fusing and circuit protection devices are required.

CAUTION

: The safe integration of the drive into a machine system is the responsibility of the

machine designer. Be sure to comply with the local safety requirements at the
place where the machine is to be used. In Europe these are the Machinery
Directive, the ElectroMagnetic Compatibility Directive and the Low Voltage
Directive. In the United States this is the National Electrical code and local codes.

CAUTION

: Drives must be installed inside an electrical cabinet that provides environmental

control and protection. Installation information for the drive is provided in this
manual. Motors and controlling devices that connect to the drive should have
specifications compatible to the drive.

CAUTION

: Violent jamming (stopping) of the motor during operation may damage the motor

and drive.

CAUTION

: Do not tin (solder) exposed wires. Solder contracts over time and may cause

loose connections. Use crimp connections where possible.

CAUTION

: Electrical components can be damaged by static electricity. Use ESD

(electro-static discharge) procedures when handling this drive.

CAUTION

: Ensure that resolver or encoder wires are properly connected. Incorrect

installation may result in improper movement.

CAUTION

: The threaded holes in the top and bottom of the enclosure are for cable clamps.

Be sure to use a M4 bolt no longer than 12mm in length. Longer bolts might
short-circuit the electrical components inside the drive.

CAUTION

: Removing the cover will invalidate UL certification.

«
...
8
9
10
11
12
...
»

Содержание Flex+DriveII































































































































Отзывы:

Нет отзывов

Похожие инструкции для Flex+DriveII

VLT AutomationDrive FC 302

Бренд: Danfoss Страницы: 346

Megatorque M-EDC-PN2012 Series

Бренд: NSK Страницы: 32

Бренд: YASKAWA Страницы: 47

Бренд: National Instruments Страницы: 28

Бренд: Moeller Страницы: 221

Бренд: Pacific Scientific Страницы: 80

Бренд: ABB Страницы: 13

Бренд: Allen-Bradley Страницы: 2

Бренд: Panasonic Страницы: 48

Бренд: Panasonic Страницы: 84

Бренд: Leadshine Страницы: 28

Бренд: Leadshine Страницы: 59

Бренд: Leadshine Страницы: 22

Бренд: BLEMO Страницы: 318

TECHNODRIVE MG 5020SC

Бренд: Twin Disc Страницы: 54

Бренд: RIB Страницы: 44

Бренд: RIB Страницы: 48

Бренд: Metronix Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды