AVZ Cubola Solidare Скачать руководство пользователя | Manualshive

Страница: 8 / 31

background image

Cubola

®

Solidare

®

EN 20-04-2018

8

Assembly Cubola

®

Solidare

®

Wall mounting Cubola

®

Solidare

®

5.

Screw the wall mounting plate to the mounting profile.

Note: Side mounting plate with holes at 50 mm (side with the most holes) against the wall mounting

plate.

6.

Slide the mounting profile into the tubular profile and temporarily fasten or deliver the support
separately with the profile.

On site, first mount the mounting profile to the wall before attaching the support beam.
Note: The wall mounting plate is available in a left and right version.

7.

On the other side, place the mounting profile (corner profile) in the support beam and fasten it with
bolts. Note: Turn the side with the most holes towards the centre of the profile so that the mounting
piece is laid 2 mm into the support beam. Note: When the profile is turned around, the corner
mounting piece will be flush with the profile.

«
...
6
7
8
9
10
...
»

Содержание Cubola Solidare
































Отзывы:

Нет отзывов

Похожие инструкции для Cubola Solidare

Бренд: Kiwi Camping Страницы: 3

Бренд: RUSTA Страницы: 8

Бренд: Ombréa Страницы: 83

Бренд: Creative Structures Страницы: 17

Бренд: Sunjoy Страницы: 4

Бренд: gaviota Страницы: 48

Бренд: Ozark Trail Страницы: 2

Бренд: Wanderer Страницы: 7

Бренд: Palram Страницы: 30

Бренд: Hilleberg Страницы: 23

Бренд: Vango Страницы: 2

Бренд: Vango Страницы: 3

Бренд: Bunker Hill Security Страницы: 8

Wonder & Wise STAR

Бренд: Asweets Страницы: 2

Wonder & Wise CAMO SCOUT TENT

Бренд: Asweets Страницы: 2

Wild Country Zonda 8EP

Бренд: TERRA NOVA Страницы: 9

Бренд: SHELTER Страницы: 13

Бренд: SHELTER Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды