AVZ Cubola Solidare Скачать руководство пользователя | Manualshive

Страница: 14 / 31

background image

Cubola

®

Solidare

®

EN 20-04-2018

14

Assembly Cubola

®

Solidare

®

Sub-composition tensioning system (systems larger than 4.0 meter)
1.

Slide the clamping plate in the slot of the front profile with the wholes to the centre of the front
profile. Make sure the sides of the clamping plate and the front profile are flush.

2.

Mark the holes and drill hole of 9 mm. Do this on both sides of the front profile. Note: Do not drill
the holes of the clamping plate.

3.

Drill holes of 6,5 mm with aid of the drilling template in the slot of the front profile. Keep about 500
mm distance between the holes. Keep a distance of 700 mm in the middle of the front profile. Note:
The distance of 700 mm is the required space for the clamp cleat during opening and closing.

4.

Slide the block to the centre of the tailored tensioning wire and screw it into place with the hexagon
screw.

ATTENTION:

Slide first the spring

support blocks in the front profile.
See item 8

– 9 page 17.

«
...
12
13
14
15
16
...
»

Содержание Cubola Solidare
































Отзывы:

Нет отзывов

Похожие инструкции для Cubola Solidare

Бренд: PAPILLON Страницы: 2

Бренд: SunnCamp Страницы: 3

Fiesta High Peak

Бренд: Fiesta Страницы: 4

Бренд: RUSTA Страницы: 44

NATIONAL GEOGRAPHIC 4007922009452

Бренд: Bresser Страницы: 16

Бренд: Ardisam Страницы: 48

Бренд: Campvalley Страницы: 2

Бренд: Ozark Trail Страницы: 6

PALLADIA flat 2

Бренд: Corradi Страницы: 23

Бренд: FarmTek Страницы: 19

Atlantis G-Gutter

Бренд: FenWall Страницы: 2

Бренд: Smittybilt Страницы: 14

power lizard sul 2-3p

Бренд: Vaude Страницы: 63

Бренд: Grand Canyon Страницы: 5

Бренд: Canopy Factory Страницы: 3

PARTY TENT 20’x20’ PE

Бренд: Delta Страницы: 8

Бренд: Sojag Страницы: 28

Бренд: KAKADU Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды