AVZ Cubola Solidare Скачать руководство пользователя | Manualshive

Страница: 22 / 31

background image

Cubola

®

Solidare

®

EN 20-04-2018

22

Installation Cubola

®

Solidare

®

25.

Feed the cord through the front profile as shown below.

26.

Remove the cord tensioner from the front profile for easier positioning of the cord on the wheels. Insert
the cord through the hole in the cord tensioner and pull lightly to tension. Make a knot in the cord at
around 25 cm behind the hole. Cut off the cord after the knot.
Note: Check that the cord runs smoothly over the wheels within the system.

27.

Place the cord tensioner in the front profile and fasten it by turning the PVC guide blocks with a
screwdriver. Tension the system, turning in the direction as shown on the cord tensioner. Note: Every
spring may be stretched to a maximum of 60% of its own length.

28.

Let the fabric run in and out a couple of times to check the correct functioning.

29.

Also check that the springs are not stretched too far.

30.

Hook the gutter onto the side guide (optional) and click it.

31.

Fasten the optional gutter to the side guide with self-drilling screws.

«
...
20
21
22
23
24
...
»

Содержание Cubola Solidare
































Отзывы:

Нет отзывов

Похожие инструкции для Cubola Solidare

Бренд: Coleman Страницы: 57

TARP VALLEY VIEW 2

Бренд: nomad Страницы: 5

Atmospheric 2 Fusion

Бренд: Woods Страницы: 8

Бренд: GentleTent Страницы: 16

Бренд: Zempire Страницы: 5

Бренд: AC Infinity Страницы: 24

FUTURE LITE 20 Wide

Бренд: Toptec Страницы: 21

Бренд: Rowlinson Garden Products Страницы: 2

Бренд: Rowlinson Garden Products Страницы: 4

WAGONTOP GARAGE

Бренд: Nemo Страницы: 8

ClearView 105657

Бренд: FarmTek Страницы: 4

Бренд: Outsunny Страницы: 4

Бренд: VITORIA Страницы: 23

Бренд: SHELTER Страницы: 12

Бренд: Quest Leisure Products Страницы: 20

Бренд: Feldon Shelter Страницы: 34

Бренд: Vango Страницы: 4

GOLDEN BEAR T-PRIVACY

Бренд: WORLD FAMOUS SPORTS Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды