AVZ Cubola Solidare Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 31

background image

Cubola

®

Solidare

®

EN 20-04-2018

7

Assembly Cubola

®

Solidare

®

Sub-composition support beams
1.

Cut the profiles to the correct lengths according to the cut lists.

2.

Place the drilling template and drill 4 holes according to the ‘support beam pattern. Do the same on
the other side of the profile.

Freestanding Cubola

®

Solidare

®

3.

Insert the corner mounting piece in the leg. Note: Turn the side with the most holes towards the centre
of the profile so that the corner mounting piece is laid 2 mm into the leg. Note: When the profile is
turned around, the corner mounting piece will be flush with the profile. This is used for wall mounting
and thus not desired for this application!.

4.

Fasten the corner mounting pieces with the bolts on the top.

«
...
5
6
7
8
9
...
»

Содержание Cubola Solidare
































Отзывы:

Нет отзывов

Похожие инструкции для Cubola Solidare

Бренд: X-METAL Страницы: 30

Бренд: Holz-Blech Страницы: 13

Бренд: Wehncke Страницы: 9

Бренд: Buffalo Tools Страницы: 2

Бренд: Alpinter Страницы: 11

Бренд: Sunjoy Страницы: 8

Бренд: Sunjoy Страницы: 8

Бренд: ROBINHOOD Страницы: 4

Бренд: NRS Relief Страницы: 2

TRIM LINE 944-07.00 Series

Бренд: Dometic Страницы: 4

Бренд: Napier Страницы: 7

Brean 4 Classic AIR

Бренд: Kampa Страницы: 12

AIRBEAM AirAway Sapera Standard

Бренд: Vango Страницы: 2

Бренд: Vango Страницы: 3

Бренд: Canopy Factory Страницы: 4

Superlight Tarp Tent 0707273933737

Бренд: DD HAMMOCKS Страницы: 2

Бренд: WeatherPort Страницы: 31

Бренд: Napier Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды