Avaya Secure Router 2330 Скачать руководство пользователя страница 9

Страница: 9 / 126

Chapter 1: Avaya Secure Router 2330/4134

safety precautions

Safety requirement for handling and installing modules

This section provides the information necessary for the proper and safe handling of hardware

components for the Avaya Secure Router 2330 and the Secure Router 4134. Please read and

apply this information to all aspects of the instructions in this manual.

Types of notices

Notice paragraphs alert you about issues that require your attention. The following paragraphs
describe the types of notices used in this guide. For translations of safety messages, see

Translations of safety messages

on page 121.

Important:

An attention notice provides important information regarding the installation and operation
of Avaya products.

Electrostatic alert:

ESD

ESD notices provide information about how to avoid discharge of static electricity and
subsequent damage to Avaya products.

Caution:

Caution notices provide information about how to avoid possible service disruption or
damage to Avaya products.

Warning:

Warning notices provide information about how to avoid personal injury when working with
Avaya products.

Installation — Hardware Components

August 2013 9

Содержание Secure Router 2330































































































































Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды

Avaya Secure Router 2330, Установка оборудования

Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды