Avaya Secure Router 2330 Скачать руководство пользователя страница 56

Страница: 56 / 126

Figure 30: Slot numbering on the Secure Router 4134

A slot numbering legend is printed directly above the chassis SFP Ethernet ports (ports 0/3

and 0/4) on the front panel of the Secure Router 4134. The legend shows how slots are

numbered on the Secure Router 4134. The following figure shows the slot numbering

legend.

Figure 31: Slot numbering legend printed on the Secure Router 4134

Slots 1–4 are Small Module slots. Slots 5–7 are Medium Module slots. If you insert a Large

Module, it spans slots 6 and 7. In this case, the Large Module is identified in the Command

Line Interface (CLI) as slot 6.

Average time to install an interface module: 1 minute.

Installing Avaya Secure Router 2330/4134 hardware components

56 Installation — Hardware Components

August 2013

Comments? [email protected]

Содержание Secure Router 2330































































































































Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды

Avaya Secure Router 2330, Установка оборудования

Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды