Avaya Secure Router 2330 Скачать руководство пользователя страница 46

Страница: 46 / 126

Figure 25: 1-port ADSL2+ Annex B Small Module

The following table lists the connectors and cables to use with the 1-port ADSL2+ Small
Modules.

Table 30: Cables and connectors

Port

Connector

Recommended

cable type

Minimum cable

length

Loop length

ADSL2
+

RJ11

24 AWG Category 5
twisted pair cable

—

17000 ft (5180 m)

Important:

Ensure that you use straight cables with ADSL2+ modules. The TIP must connect to TIP
and RING must connect to RING.

The following table describes the LED status for the 1-port ADSL2+ Small Modules.

Table 31: Module LEDs

LED

Description

STAT

Status of general module:

• Off—No power available to the module.

• Yellow—Out of service, or failed to initiate.

• Green—Power on and the module is operational.

LINK/STAT 1

Status of interface 1

• Off—Not connected or the interface is out of service.

• Yellow—The interface is in a loopback mode or is running

diagnostics.

• Green—The link or channel is active and receiving a valid signal.

Avaya Secure Router 2330/4134 hardware components fundamentals

46 Installation — Hardware Components

August 2013

Comments? [email protected]

Содержание Secure Router 2330































































































































Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды

Avaya Secure Router 2330, Установка оборудования

Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды