Avaya Secure Router 2330 Скачать руководство пользователя страница 84

Страница: 84 / 126

6. Firmly grasp the DIMM by its edges and pull the DIMM from the slot.
7. If you are replacing the DIMM, also see

Installing a DIMM on the Mediation Server

Module

on page 81.

If you are not installing a DIMM at this time, replace the module in the slot, or place

a slot cover plate over the slot from which you removed the module. Store the

Mediation Server Module in an antistatic bag until you are ready to install it in the

chassis.

Replacing the Secure Router 4134 internal Compact Flash

Use the instructions in this section if you must replace the internal Compact Flash. This internal

device is not hot swappable.

Average time to replace the internal Compact Flash: 1 minute

Caution:

Do not open the Secure Router 4134 service access panel while the unit is powered.

Important:

The internal Compact Flash that ships with the Secure Router 4134 contains the system

image.

Prerequisites

• Ensure you have a replacement Compact Flash ready to install.
• Ensure you have a Phillips #2 screwdriver.

Installing Avaya Secure Router 2330/4134 hardware components

84 Installation — Hardware Components

August 2013

Comments? [email protected]

Содержание Secure Router 2330































































































































Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды

Avaya Secure Router 2330, Установка оборудования

Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды