Avaya Secure Router 2330 Скачать руководство пользователя страница 81

Страница: 81 / 126

Electrostatic alert:

To prevent damage from electrostatic discharge, always wear an antistatic wrist strap

connected to an electrostatic discharge (ESD) jack when performing maintenance on this

product. Ensure that the wrist strap makes contact with your skin.

Installing a DIMM on the Mediation Server Module

Use the procedure in this section if you must install a DIMM on the Mediation Server

Module.

Average time to install a DIMM on the Mediation Server Module: 3 minutes.

Prerequisites

• Ensure the Secure Router 4134 is powered down.
• Ensure you have a Phillips #2 screwdriver.
• Ensure you have antistatic material available on which to lay the Mediation Server Module

while you work.

• Ensure you have a DIMM ready to install before opening the service access panel.

Procedure steps

1. Using a Phillips screwdriver, loosen the two captive screws that secure the

Mediation Server Module to the chassis. The following figure shows the screws.

2. Using the lever on the module, pull the module straight out of the chassis slot.

Support the module as you remove it from the chassis by grasping it by the

edges.

3. Ensure you place the Mediation Server Module on antistatic material if you lay it

down to install a DIMM.

Always hold the module by its edges.

Installing or removing the DIMM on the Secure Router 4134 Mediation Server Module for OCS

Installation — Hardware Components

August 2013 81

Содержание Secure Router 2330































































































































Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды

Avaya Secure Router 2330, Установка оборудования

Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды