Avaya Secure Router 2330 Скачать руководство пользователя страница 19

Страница: 19 / 126

Chapter 4: Avaya Secure Router 2330/4134

hardware components
fundamentals

This section provides an overview of the Avaya Secure Router 2330/4134 hardware components.

For information about installing the Secure Router 4134 chassis, see

Avaya Secure Router 4134

Installation — Chassis

(NN47263-300).

For information about installing the Secure Router 2330 chassis, see

Avaya Secure Router 2330

Installation — Chassis

(NN47263-304).

For information about initial configuration of the Secure Router 2330/4134, see

Avaya Secure Router

2330/4134 Commissioning

(NN47263-302).

Secure Router 4134 Power supply units

Important:

The information in this section is not applicable to the Secure Router 2330.

The Secure Router 4134 offers flexible power supply options. Power supplies are available in
the following wattage:

• 250 W AC

• 660 W AC (410 W available for PoE)

• 250 W DC

The Secure Router 4134 has two slots for power supply units. You can install single or dual
power supply modules in any of the following configurations:

• one or two standard AC input modules

• one or two Power over Ethernet (PoE) AC input modules

• one standard AC and one PoE AC input module

• one or two DC modules

• one AC (standard or PoE) and one DC module

Installation — Hardware Components

August 2013 19

Содержание Secure Router 2330































































































































Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды

Avaya Secure Router 2330, Установка оборудования

Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды