Avaya Secure Router 2330 Скачать руководство пользователя страница 58

Страница: 58 / 126

Installing a Medium Module on the Secure Router 4134

Use the instructions in this section to install Medium Modules.

Procedure steps

1. Using a Phillips screwdriver #2, remove the slot cover plate from the slot in which

you are installing the module.

2. Align the module with the slot and the slot module guides.
3. Slide the module into the chassis until its connector panel touches the chassis back

panel.

4. Push gently, but firmly, to seat the connector on the interface module in the chassis

back panel.

5. Ensure the lever on the module is flush with the front panel of the Secure Router

4134.

6. Using a Phillips screwdriver, tighten the two captive screws to secure the module

to the chassis.

Installing a Large Module on the Secure Router 4134

Install the Large Module in slots 6–7 only.

Procedure steps

1. Using a Phillips screwdriver #2, remove the slot cover plates from slots 6 and 7.
2. Loosen the captive screw at the top of the center slot module guide.
3. Remove the center slot module guide. The following figure shows the removal of

the center slot guide.

Installing Avaya Secure Router 2330/4134 hardware components

58 Installation — Hardware Components

August 2013

Comments? [email protected]

Содержание Secure Router 2330































































































































Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды

Avaya Secure Router 2330, Установка оборудования

Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды