manualshive.com logo in svg

Avaya Secure Router 2330, Установка оборудования

Поделиться
Скачать
Avaya Secure Router 2330 Скачать руководство пользователя страница 72

Removing the internal VPN/IPSec module

Use the procedure in this section to remove a VPN/IPSec module from the Secure Router

4134.

 Caution:

The internal VPN/IPSec module is not hot swappable. Do not open the Secure Router 4134

service access panel while the unit is powered.

Prerequisites

• Ensure you have a Phillips #2 screwdriver.
• Ensure the Secure Router 4134 has the power switched off.
• Ensure you have an antistatic bag or sheet available for the VPN/IPSec that you are

removing.

Procedure steps

1. Remove the two screws at the rear of the Secure Router 4134 that hold the service

access panel secure. Remove these two screws only. See the following figure.

2. Slide the access panel toward you until it is clear of the Secure Router 4134.
3. Remove the two screws that secure the VPN/IPSec module to the Main Board (see

the following figure).

Installing Avaya Secure Router 2330/4134 hardware components

72     Installation — Hardware Components

August 2013

Comments? [email protected]

Содержание Secure Router 2330































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды